You will own the hardware and firmware layer of the Health Kiosk, from first prototypes through production release. That means carrier board bring-up, PCB schematic capture and layout, all UART/USB and Bluetooth sensor drivers, the isolated patient-side electronics, the power subsystem, OTA, and the test infrastructure that gates every phase. This is a full-stack embedded role. You will work directly with the ASR/ML team on the audio pipeline, the software platform team on FHIR and HMIS adapters, QA on IEC 60601-1 and ISO 14971, and manufacturing on DFM, harness, and the calibration line. Three hardware bundles ship from the same shell — Core, Clinical+, and Complete — and you must have each bundle's additional sensors driver-ready before the corresponding production build.
What You'll Own
1. PCB Design & Hardware Bring-up
- Design PCBs from schematic capture to layout using KiCad or Altium.
- Develop carrier boards, isolated patient-side circuits, biosignal front-end, and power subsystem boards.
- Select components using datasheets, maintain BOMs, and coordinate DFM reviews.
- Bring up SoC carrier boards involving USB 3.2, MIPI CSI-2, M.2, HDMI, and GPIO.
- Validate hardware using logic analysers and oscilloscopes.
- Design and verify isolated patient-side electronics with 2×MOPP barriers and isolated DC-DC converters.
- Implement ECG front-end using ADS1293, including right-leg drive, common-mode rejection, and plate-contact detection.
- Design power subsystems involving 24V medical PSU, LiFePO₄ BMS, and UPS switchover.
2. Firmware & Embedded Software
- Develop and maintain JetPack Linux service containers using Docker.
- Implement UART/TTL drivers for medical-grade sensors.
- Develop Bluetooth LE drivers and manage radio scheduling to prevent audio dropouts.
- Implement OCR fallback pipelines for sensor readings.
- Control ROBOTIS Dynamixel XL430 pan-tilt servos using U2D2/TTL bus.
- Implement face-tracking loops at ≤20 Hz, including soft stops and servo scheduling.
- Manage USB device trees and Linux subsystems such as V4L2, ALSA, SANE, and HID.
- Develop firmware services using Python or C++.
3. OTA, Security & Fleet Management
- Build and maintain signed OTA pipelines using Ed25519 firmware signing.
- Implement A/B partitioning, watchdog rollback, and model hot-swapping without reboot.
- Develop fleet telemetry to monitor:
- Per-unit uptime.
- UART timeout counts.
- Bluetooth pairing failures.
- NVMe SMART health.
- Implement store-and-forward telemetry over LTE.
- Ensure encrypted patient records, secure OTA updates, and consent management.
- Maintain compliance with the DPDP Act 2023.
4. Compliance, Testing & Validation
- Contribute to compliance requirements under:
- IEC 60601-1 – Electrical Safety.
- IEC 60601-1-2 – Electromagnetic Compatibility.
- IEC 62304 – Medical Device Software Lifecycle.
- ISO 14971 – Risk Management.
- ISO 13485 – Quality Management System.
- Design and validate PCBs for patient leakage current, dielectric strength, ESD immunity, and EMC emissions.
- Build calibration station fixtures and hardware bench-testing rigs.
- Conduct EVT and DVT acceptance testing.
- Contribute to DHR and DMR documentation in ERPNext.
- Coordinate pre-compliance EMC scans, formal IEC lab testing, and CDSCO/BIS filing support.
Required Skills & Experience
- 3–5 years of hands-on experience in embedded hardware and firmware development.
- Exposure to medical devices or regulated product development.
- Strong PCB schematic capture and layout experience using KiCad or Altium.
- Experience designing multi-layer PCBs that have gone into production.
- Knowledge of component selection, BOM management, and DFM reviews.
- Experience testing PCBs against industry standards, including isolation barriers, leakage current, and EMC pre-compliance.
- Hands-on experience with Embedded Linux on ARM SoCs.
- Knowledge of systemd, Docker, device trees, U-Boot, and secure boot.
- Experience developing UART/TTL and Bluetooth LE peripheral drivers using vendor protocol documentation.
- Understanding of USB device tree management and Linux subsystems.
- Knowledge of power electronics, including DC-DC converters, BMS, UPS switchover logic, and rail sequencing.
- Proficiency with logic analysers and oscilloscopes for hardware debugging.
- Programming experience in Python or C++.
- Ability to collaborate with QA, regulatory affairs, and manufacturing teams.
- Experience reading and contributing to risk management documentation.
Good to Have
- Experience with formal IEC 60601-1 or IEC 60601-1-2 laboratory testing.
- Exposure to ISO 13485 QMS, including DHR/DMR documentation, supplier qualification, and calibration SOPs.
- Experience implementing Bluetooth LE GATT profiles from scratch.
- Experience designing OTA pipelines involving A/B partitioning, signed firmware, and watchdog rollback.
- LTE modem bring-up experience under Linux.
- Experience working with medical sensor OEMs.