MACHINIST INSPECTOR

Security Clearance

Secret

Duties

You will be responsible for certification of Naval Special Emphasis Program (NSEP) material to include Level 1, Scope of Certification (SOC), Fly-By-Wire, for all submarine and surface fleet activities.,You will work alongside other Machined Parts Inspectors, demonstrating proper work/inspection methods.,You will perform tracking contract progress and shipping materials to the vendor site to perform the next off site inspection which includes communicating with DCMA and the vendor to set up the inspections.,You will assure safety requirements are followed, including proper use of tools and equipment.,You will serve as primary on-site inspection representative in the absence of the foreman.

Qualifications

Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on the quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element will be found ineligible. The Screen-out Element for this position is: Ability to Inspect as a Machinist Inspector , WG-3414-12 while performing the following duties: Demonstrating thorough knowledge of, and skill in, non-nuclear machined parts inspection processes. Reviewing job orders and other work authorization and/or work description documents and ensuring required technical procedures, plans, blueprints, materials and tools are available. Reviewing work status in progress and when completed to ensure instructions on inspection sequence and deadlines have been met. Working alongside other Machined Parts Inspectors, demonstrating proper work/inspection methods. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=List-of-Approved-Job-Elements Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment.

Other Information

This position is covered by the Department of Defense Priority Placement Program. Additional vacancies may be filled by this announcement. A tentative offer of employment will be rescinded if the selectee fails to meet the pre-employment requirements, including failure to report to any of the scheduled appointments. Primary duties are performed inside in a well-lit, shop type work environment but could be outdoors, in all types of weather conditions. Incumbent could be exposed to extreme cold or heat, smoke, dust, noise, fumes, poor illumination, unpleasant odors and dampness on a daily basis. May be required to wear protective clothing and equipment that could be heavy, awkward and uncomfortable. Frequently, may be exposed to the possibility of cuts, bruises, and broken bones. May be required to work in nuclear areas for short periods of time. Federal Annuitant Information: The selection of an annuitant is subject to the Department of Defense and Department of the Navy policy on the employment of annuitants. Policy information may be found at: https://www.secnav.navy.mil/donhr/documents/civilianjobs/fedcivannuitants.pdf PPP applicants will be placed at the FPL, if determined Well Qualified (WQ). To receive priority consideration, the FPL must be the same grade level or equivalent of the retained grade or the grade held immediately prior to separation. Interagency Career Transition Assistance Program (ICTAP): In addition to meeting all minimum qualification and eligibility requirements, displaced federal employees must be well qualified for the position to receive consideration for special priority selection. A well-qualified ICTAP applicant is one who possesses the competencies and experience to perform the duties of the position successfully with orientation to learn/understand the activities, procedures, policies and processes. To be considered well-qualified and exercise selection priority as an ICTAP candidate, displaced Federal employees must satisfy all qualification requirements for the position and receive a rating of 85 or higher. Demonstrated work experience in the occupation is typically qualifying for placement. This criterion cannot be met by education and training. ICTAP candidates must provide copies of all of the following documentation at the time of application: 1) agency notice; 2) most recent performance appraisal; and 3) most recent SF-50 or notification of personnel action that includes position, grade level, and duty location. Applicants who do not provide this documentation will not receive consideration as an ICTAP candidate. For more information about ICTAP eligibility, please review the following link: https://help.usajobs.gov/working-in-government/unique-hiring-paths/federal-employees/career-transition Military Spouse Preference applicants will be placed at the highest grade for which they have applied and are determined Best Qualified (BQ). A BQ military spouse possesses knowledge, skills, abilities, and competencies comparable to others who meet the competitive referral criteria for the specific position.

Conducting maritime military operations and maintaining naval defense readiness.